Pipe Fittings

A reducer is a component in a pipeline that reduces the pipe size from a larger to a smaller bore (inner diameter).

The length of the reduction is usually equal to the average of the larger and smaller pipe diameters. There are two main types of reducer:

concentric and eccentric reducers.

A reducer can be used either as a nozzle or as diffuser depending on the mach number of the flow.

A reducer allows for a change in pipe size to meet hydraulic flow requirements of the system or to adapt to existing piping of a different size. Reducers are usually concentric but eccentric reducers are used when required to maintain the same top-or bottom-of-pipe level.

These fittings are manufactured in inch and metric size.

An eccentric reducer is a fitting used in piping systems between two pipes of different diameters. They are used where the diameter of the pipe on the upstream side of the fitting (i.e. where the flow is coming from) is larger than the downstream side. Unlike a concentric reducer, which resembles a cone, eccentric reducers have an edge that is parallel to the connecting pipe. This parallel edge results in the two pipes having offset center lines. The same fitting can be used in reverse as an eccentric increaser/expander.

Horizontal liquid reducers are always eccentric, top flat (unless on control set, same as PV, TV, HV, LV) or (pipe rack), which prevents the build-up of air bubbles in the system. Eccentric reducers are used at the suction side of pumps to ensure air does not accumulate in the pipe. The gradual accumulation of air in a concentric reducer would result in a large bubble that could eventually cause the pump to stall or cause cavitation when drawn into the pump.

The word eccentric in regards to piping is commonly pronounced "e-sentrik" (spelled "ecentric"). This has become an industry standard and is widely taught in schools.

Horizontal gas reducers are always eccentric, bottom flat, which allows condensed water or oil to drain at low points.

Reducers in vertical lines are generally concentric unless the layout dictates otherwise.

Concentric Reducer

A reducer is a component in a pipeline that reduces the pipe size from a larger to a smaller bore (inner diameter).

The length of the reduction is usually equal to the average of the larger and smaller pipe diameters. There are two main types of reducer: concentric and eccentric reducers.

A reducer can be used either as a nozzle or as diffuser depending on the mach number of the flow.

A reducer allows for a change in pipe size to meet hydraulic flow requirements of the system or to adapt to existing piping of a different size. Reducers are usually concentric but eccentric reducers are used when required to maintain the same top-or bottom-of-pipe level.

These fittings are manufactured in inch and metric size.

Other details:

• Stainless Steel: ASTM A403 WP 304, 304L, 304H, 316, 316L, 317, 317L, 321, 310, 347, 904L
• Carbon Steel: ASTM A234 WPB, A420 WPL3, A420 WPL6, MSS-SP-75 WPHY 42, 46, 52, 56, 60, 65, 70
• Alloy Steel: ASTM A234 WP1, WP5, WP9, WP11, WP22, WP91
• Others: Monel, nickel, inconel, hastelloy, copper, brass, bronze, titanium, tantalum, bismuth, aluminum, high speed steel, zinc and lead

Duplex Tee

Duplex Pipe Fittings are the widely chosen fittings, used in critical conditions of industries. Widely demanded in the industries of oil & gas, petrochemical, and many others, these fittings are designed with the assurance of dimensional accuracy, resistance against corrosion and high tolerance capacity. Designed in the options of threaded and socket weld end connections, the pipe fittings have either buttweld, seamless or welded construction. These have the ability to bear a wide range of pressure level with excellent inertness to toxic chemicals. Best suited for highly critical applications where leakage can be hazardous, the pipe fittings are used in boilers, desalination plants and brewing tanks. There are minimum burrs at the edge of the fittings with excellent accuracy in dimensions even in high-temperature range. Due to their high yield strength, these are widely demanded in the petrochemical industry, nuclear industry, paper & pulp industry and defense sector.

Fittings generally produce the change in geometry and its application include:

• Change in direction of piping
• Alter piping dimensions
• Terminate piping line
• Brings pipes together (make the branch from main pipe run)
• Reference standard ASME B 16.9
• Use of these fittings are generally not restricted in most of the piping systems
• Difficult for small sizes, especially for thin wall
• Straight: Braches to the same pipe size as the run
• Reducing: Branches to smaller pipe size than the run
• Bullhead: Branches to bigger pipe size than the run, seldom used, made for the special purpose only.

Duplex steel grades : ASTM A 815 UNS S31803, S32205.

Details:

• Reducing tee, 3 / 4" x 3 / 4" x 1 / 2"
• Reducing tee, 1" x 1" x 1 / 2"
• Reducing tee, 1-1 / 2" x 1-1 / 2" x 3 / 4"
• Reducing tee, 1 / 2" x 1 / 2" x 1 / 8"
• Reducing tee, 2" x 2" x 1"
• Reducing tee, 2" x 2" x 1-1 / 2"
• Reducing tee, 2" x 2" x 3 / 4"
• Reducing tee, 3" x 3" x 2"

Primarily used for plumbing purposes, the offered product is manufactured using quality approved raw material and innovative technology under the direction of our adroit professionals. This product is examined on various benchmarks to assure its flawlessness. Furthermore, we provide this Super Duplex S32750 Tee in numerous dimensions as per clients' specific requirements at pocket-friendly prices.

Features:

• Sturdy construction leads to withstand high pressure
• High tensile strength and rigid structure
• Anti-corrosive property that enhances its durability
• Polished with quality approved chemical that assures its rust proof nature
• Sturdy design with accurate dimensions
• Abrasion resistance to superior dimensional stability

 

 Fittings generally produce a change in geometry and its application include:

• Change in direction of piping
• Alter piping dimensions
• Terminate piping line
• Brings pipes together (make a branch from main pipe run).
• Reference standard ASME B 16.9
• Use of these fittings are generally not restricted in most of the piping systems

 

Other details:

• Class: 3000 LBS, 6000 LBS, 9000 LBS
• Type: Socket Weld (S / W) & SCREWED (SCRD)–NPT, BSP, BSPT

Details:

• Reducing tee, 3 / 4" x 3 / 4" x 1 / 2"
• Reducing tee, 1" x 1" x 1 / 2"
• Reducing tee, 1-1 / 2" x 1-1 / 2" x 3 / 4"
• Reducing tee, 1 / 2" x 1 / 2" x 1 / 8"
• Reducing tee, 2" x 2" x 1"
• Reducing tee, 2" x 2" x 1-1 / 2"
• Reducing tee, 2" x 2" x 3 / 4"
• Reducing tee, 3" x 3" x 2"

Hastelloy Tee

· It is a hard and ductile metal of silver-white color.

· It has high corrosion resistance suitable for both high and low-temperature applications.

· Nickel is a fair conductor of heat and electricity making it suitable for its use in furnaces, heat exchangers, aerospace engineering etc.

· Nickel has high metallurgical stability making it suitable for hard-metal industry.

· It also acts as a catalyst for various chemical processes.

· Important characteristics include corrosion & oxidation resistance, ductility, brilliant polish, excellent mechanical strength, high creep resistance, high-temperature resistance.

Details:

• Reducing tee, 3 / 4" x 3 / 4" x 1 / 2"
• Reducing tee, 1" x 1" x 1/2"
• Reducing tee, 1-1 / 2" x 1-1 / 2" x 3 / 4"
• Reducing tee, 1 / 2" x 1 / 2" x 1 / 8"
• Reducing tee, 2" x 2" x 1"
• Reducing tee, 2" x 2" x 1-1 / 2"
• Reducing tee, 2" x 2" x 3 / 4"
• Reducing tee, 3" x 3" x 2"

Cross Fittings We offer a wide-ranging Cross Fitting to our clients across the country. Our range is designed and developed in cycle with the latest technological advancements in the market. 01. Cross Fittings Designed as per international standards, Cross Fittings are manufactured by us to provide zero leaks with full flow connection in hydraulic systems. These are available in fractional sizes range from 1/8 inches Tube OD to 1-inch tube OD and metric sizes ranging from 6mm to 25mm. Male Pipe Thread sizes range from 1/8 inches NPT to 1-inch NPT.

· Application for engineering purpose, for water, gas & sewerage, carbon steel tubes for idlers of belt conveyors, water wells and lancing pipes for various automotive & industrial applications

· In addition, some of the value-added Carbon Steel products include steel for LPG cylinders, API grade, corrosion resistant steel, critical structural application steel, boiler quality, auto grades, precision tubes and medium/high carbon grades, among others.

Super Duplex Cap

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high density steel and brass to provide the leakage proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

 

Duplex Cap Closures

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high-density steel and brass to provide the leakage-proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

 

Hastelloy Cap

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high-density steel and brass to provide the leakage-proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

Hastelloy Tee

· It is a hard and ductile metal of silver-white color.

· It has high corrosion resistance suitable for both high and low-temperature applications.

· Nickel is a fair conductor of heat and electricity making it suitable for its use in furnaces, heat exchangers, aerospace engineering etc.

· Nickel has high metallurgical stability making it suitable for hard-metal industry.

· It also acts as a catalyst for various chemical processes.

· Important characteristics include corrosion & oxidation resistance, ductility, brilliant polish, excellent machine strength, high creep resistance, high-temperature resistance.

 

SS Cross

We offer a wide-ranging Cross Fitting to our clients across country. These products are manufactured by using the premium quality heavy strength Steel, Brass and other raw material. Pressure testing is conducted at our manufacturing facility for effective and long-lasting performance. Our range is designed and developed in cycle with the latest technological advancements in the market. 01. Cross Fittings Designed as per international standards, Cross Fittings are manufactured by us to provide zero leaks with full flow connection in hydraulic systems. These are available in fractional sizes range from 1/8 inches Tube OD to 1 inch tube OD and metric sizes range from 6mm to 25mm. Male Pipe Thread sizes range from 1/8 inches NPT to 1 inch NPT. The products are also customized as per specifications also.

· Straight: Braches to the same pipe size as the run.

· Reducing: Branches to smaller pipe size than the run (rarely used).

Features:

Application in high demanding industries and sectors, particularly high temperature and corrosive services.

Stainless steel are reliable long lasting and at par with international quality and safety norms

Stainless Steel ERW, EFW cross fittings

· Applications include attractive appearance, corrosion resistance, low maintenance and strength of stainless steel.

· Stainless steel is more expensive than standard grades of steel but it has greater resistance to corrosion, needs low maintenance and has no need for painting or other protective coatings.

· These factors mean stainless steel can be more economically viable once service life and life-cycle costs are considered.

• Robust structure
• Fine Finish
• Precise design

 

Fittings are manufactured from materials consisting of forgings, bar, SMLS tubular products which shall conform to the requirement for WP SMLS manufacturing materials of ASTM Fitting specifications A 234, A 403, A 420, A 815, B 366 or ASTM forging specifications A 105, A 182, A 350, B 283, B 462, B 564

Socket welding

Reference standard ASME B 16.11

Size frequently limited to NPS ≤ 4” in following classes

· Not used in severe cyclic conditions and in services where corrosion is accelerated in the crevices.

· No weld metal can enter Bore

· Easier alignment of smaller lines than Butt weld fittings

· Tacking procedure is not necessary, therefore reducing welding time.

· No chance of leakage

2. Threaded

· Non-toxic, Environment-friendly and cost-effective as no welding is involved.

· Chances of leakage are comparatively higher, generally not used where leaks cannot be tolerated.

· Size frequently limited to NPS ≤ 4” in following classes

 

Used in services where regular maintenance is required.

All fittings are threaded both internal(Female) and external(Male) with American National Standard Pipe Threads ASME B1.20.1 (NPT) or British Standard Pipe Threads (BSP)

Additional information:

• Class: 3000 LBS, 6000 LBS, 9000 LBS
• Type: Socket Weld (S / W) & Screwed (SCRD)–NPT, BSP, BSPT
• Form: Reducing Tee, Unequal Tee, Equal Tee

Inconel Tee

It is a hard and ductile metal of silver-white color. It has high corrosion resistance suitable for both high and low-temperature applications. Nickel is a fair conductor of heat and electricity making it suitable for its use in furnaces, heat exchangers, aerospace engineering etc.

Nickel has high metallurgical stability making it suitable for hard-metal industry. It also acts as a catalyst in various chemical processes.

Important characteristics include corrosion & oxidation resistance, ductility, brilliant polish, excellent mechanical strength, high creep resistance, high-temperature resistance.

 

Other details:

• Class: 3000 LBS, 6000 LBS, 9000 LBS
• Type: Socket Weld (S / W) & SCREWED (SCRD)–NPT, BSP, BSPT

Details:

• Reducing tee, 3 / 4" x 3 / 4" x 1 / 2"
• Reducing tee, 1" x 1" x 1 / 2"
• Reducing tee, 1-1 / 2" x 1-1 / 2" x 3 / 4"
• Reducing tee, 1 / 2" x 1 / 2" x 1 / 8"
• Reducing tee, 2" x 2" x 1"
• Reducing tee, 2" x 2" x 1-1 / 2"
• Reducing tee, 2" x 2" x 3 / 4"
• Reducing tee, 3" x 3" x 2"

Titanium Cap

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high-density steel and brass to provide the leakage-proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

Our Titanium inventories and supplies numerous standard and reducing Cap Closures options. These Closures are available in both Titanium Grades 2 & 7. These Cap Closures are offered in many different schedules and sizes.

Inconel Cap

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high-density steel to provide the leakage-proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

SS Cap

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high-density steel to provide the leakage-proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

Cap Closure

Closure cap or flats are used to terminate a piping line.We offer an extensive range of Pipe End Closures made to international standards in a wide range to fit tubes of 6mm or ¼ inch to 35/38 mm to 1-1/2 inches. These Pipe End Closures are manufactured by using the high density steel to provide the leakage proof function. These Pipe End Closures are available in different lengths and diameters to serve varied applications and is made of finest quality. This range is available in various size and specification as per the requirement of the clients.

Carbon Steel: ASTM A234 WPB, A420 WPL3, A420 WPL6, MSS-SP-75 WPHY 42, 46, 52, 56, 60, 65, 70